Messages

1

Parallel Port breakout boards, motherboards, and dedicated accessories / Re: Cannot get PMDX-107 to Do Test Mode?

« on: July 20, 2015, 02:13:01 PM »

Thanks Steve for all the help today.

Corrupted Mach 3 Config File was the issue.

2

Parallel Port breakout boards, motherboards, and dedicated accessories / Re: Cannot get PMDX-107 to Do Test Mode?

« on: July 20, 2015, 11:04:01 AM »

Seems it will only run clockwise. M3 & M4 do nothing if I go to pulleys and select reverse it will run reverse counter clockwise.

I followed the AN002 instructions.

Wonder what setting I am missing?

3

Parallel Port breakout boards, motherboards, and dedicated accessories / Re: Cannot get PMDX-107 to Do Test Mode?

« on: July 20, 2015, 02:49:26 AM »

Got it! Was a bad wire.

4

Parallel Port breakout boards, motherboards, and dedicated accessories / Cannot get PMDX-107 to Do Test Mode?

« on: July 20, 2015, 12:52:20 AM »

I cannot get the 107 to talk to the VFD. Test Mode when it exits it does give it some com when A001 is set to control terminal and A002 is set to key pad and switched to run. When Hooked to a POT it works as it should just not with the PMDX-107.  PMDX-126 W/ESS

VFD is a HITACHI WJ200-022SF Settings. See Quick Reference Page 50: http://www.hitachi-america.us/supportingdocs/forbus/inverters/Support/NT3251X.pdf

A001 set at 01 Even Tried 00 (A001: 01 Control Terminal, 00 Pot Control On Ext Operator   
A002 Set to 01 Control Terminal
PLC is jumped to L on upper row "Source Logic"  (Page 27)

Connecting the 107 to the VFD

Rev/Dir  to Terminal 2 on VFD
Fwd/Run to Terminal 1 on VFD
COM ? P24 on VFD
Aref  to H on VFD
Aout  to O on VFD
Agnd - L on lower row on VFD
Dip 6 On For RatioMetric (Tried it Both Ways On and off).

Am I doing something Wrong In the hookup or settings? 

5

Parallel Port breakout boards, motherboards, and dedicated accessories / Re: Feed Rate & Spindle Speed Override Wiring?

« on: July 19, 2015, 08:35:29 PM »

Thanks Steve

Connections PMDX-107 to WJ200-022SF

Rev/Dir  to Terminal 2 on VFD
Fwd/Run 1 to Terminal 3 on VFD
COM to P24 on VFD or + 24 on External Power Supply
Aref  to H on VFD
Aout  to O on VFD
Agnd - L on lower row on VFD

6

Parallel Port breakout boards, motherboards, and dedicated accessories / Re: Feed Rate & Spindle Speed Override Wiring?

« on: July 17, 2015, 06:11:36 PM »

I am thinking a 3PDT Switch or Relay for the Speed Pot? To be able to Select Automated Mach Control or Manual Pot Control? No to Concerned right now about the federate override.

7

Parallel Port breakout boards, motherboards, and dedicated accessories / Feed Rate & Spindle Speed Override Wiring?

« on: July 14, 2015, 10:11:25 AM »

Using a PMDX 126 W/ESS, PMDX 107, HITACHI WJ200-022SF VFD

Wondering if anyone has a wiring info/diagrams for a Feed Rate & Spindle Speed Override. Or if it is Possible using mach 3.

Ideally would like to add 2 potentiometers to the machine to control both?

Thanks.

8

General Discussion / Thanks For The Support Forum..

« on: November 23, 2014, 08:55:00 PM »

Awaiting My PMCX-126 should be here next week.